© COPYRIGHT 2011 STMicroelectronics
+ ******************************************************************************
+ */
+
+/** @addtogroup CMSIS
+ * @{
+ */
+
+/** @addtogroup stm32f4xx
+ * @{
+ */
+
+#ifndef __STM32F4xx_H
+#define __STM32F4xx_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif /* __cplusplus */
+
+/** @addtogroup Library_configuration_section
+ * @{
+ */
+
+/* Uncomment the line below according to the target STM32 device used in your
+ application
+ */
+
+#if !defined (STM32F4XX)
+ #define STM32F4XX
+#endif
+
+/* Tip: To avoid modifying this file each time you need to switch between these
+ devices, you can define the device in your toolchain compiler preprocessor.
+ */
+
+#if !defined (STM32F4XX)
+ #error "Please select first the target STM32F4XX device used in your application (in stm32f4xx.h file)"
+#endif
+
+#if !defined (USE_STDPERIPH_DRIVER)
+/**
+ * @brief Comment the line below if you will not use the peripherals drivers.
+ In this case, these drivers will not be included and the application code will
+ be based on direct access to peripherals registers
+ */
+ /*#define USE_STDPERIPH_DRIVER*/
+#endif /* USE_STDPERIPH_DRIVER */
+
+/**
+ * @brief In the following line adjust the value of External High Speed oscillator (HSE)
+ used in your application
+
+ Tip: To avoid modifying this file each time you need to use different HSE, you
+ can define the HSE value in your toolchain compiler preprocessor.
+ */
+
+#if !defined (HSE_VALUE)
+ #define HSE_VALUE ((uint32_t)25000000) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+/**
+ * @brief In the following line adjust the External High Speed oscillator (HSE) Startup
+ Timeout value
+ */
+#if !defined (HSE_STARTUP_TIMEOUT)
+ #define HSE_STARTUP_TIMEOUT ((uint16_t)0x0500) /*!< Time out for HSE start up */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+#if !defined (HSI_VALUE)
+ #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+ * @brief STM32F4XX Standard Peripherals Library version number V1.0.0
+ */
+#define __STM32F4XX_STDPERIPH_VERSION_MAIN (0x01) /*!< [31:24] main version */
+#define __STM32F4XX_STDPERIPH_VERSION_SUB1 (0x00) /*!< [23:16] sub1 version */
+#define __STM32F4XX_STDPERIPH_VERSION_SUB2 (0x00) /*!< [15:8] sub2 version */
+#define __STM32F4XX_STDPERIPH_VERSION_RC (0x00) /*!< [7:0] release candidate */
+#define __STM32F4XX_STDPERIPH_VERSION ((__STM32F4XX_STDPERIPH_VERSION_MAIN << 24)\
+ |(__STM32F4XX_STDPERIPH_VERSION_SUB1 << 16)\
+ |(__STM32F4XX_STDPERIPH_VERSION_SUB2 << 8)\
+ |(__STM32F4XX_STDPERIPH_VERSION_RC))
+
+/**
+ * @}
+ */
+
+/** @addtogroup Configuration_section_for_CMSIS
+ * @{
+ */
+
+/**
+ * @brief Configuration of the Cortex-M4 Processor and Core Peripherals
+ */
+#define __CM4_REV 0x0001 /*!< Core revision r0p1 */
+#define __MPU_PRESENT 1 /*!< STM32F4XX provides an MPU */
+#define __NVIC_PRIO_BITS 4 /*!< STM32F4XX uses 4 Bits for the Priority Levels */
+#define __Vendor_SysTickConfig 0 /*!< Set to 1 if different SysTick Config is used */
+#define __FPU_PRESENT 1 /*!< FPU present */
+
+/**
+ * @brief STM32F4XX Interrupt Number Definition, according to the selected device
+ * in @ref Library_configuration_section
+ */
+typedef enum IRQn
+{
+/****** Cortex-M4 Processor Exceptions Numbers ****************************************************************/
+ NonMaskableInt_IRQn = -14, /*!< 2 Non Maskable Interrupt */
+ MemoryManagement_IRQn = -12, /*!< 4 Cortex-M4 Memory Management Interrupt */
+ BusFault_IRQn = -11, /*!< 5 Cortex-M4 Bus Fault Interrupt */
+ UsageFault_IRQn = -10, /*!< 6 Cortex-M4 Usage Fault Interrupt */
+ SVCall_IRQn = -5, /*!< 11 Cortex-M4 SV Call Interrupt */
+ DebugMonitor_IRQn = -4, /*!< 12 Cortex-M4 Debug Monitor Interrupt */
+ PendSV_IRQn = -2, /*!< 14 Cortex-M4 Pend SV Interrupt */
+ SysTick_IRQn = -1, /*!< 15 Cortex-M4 System Tick Interrupt */
+/****** STM32 specific Interrupt Numbers **********************************************************************/
+ WWDG_IRQn = 0, /*!< Window WatchDog Interrupt */
+ PVD_IRQn = 1, /*!< PVD through EXTI Line detection Interrupt */
+ TAMP_STAMP_IRQn = 2, /*!< Tamper and TimeStamp interrupts through the EXTI line */
+ RTC_WKUP_IRQn = 3, /*!< RTC Wakeup interrupt through the EXTI line */
+ FLASH_IRQn = 4, /*!< FLASH global Interrupt */
+ RCC_IRQn = 5, /*!< RCC global Interrupt */
+ EXTI0_IRQn = 6, /*!< EXTI Line0 Interrupt */
+ EXTI1_IRQn = 7, /*!< EXTI Line1 Interrupt */
+ EXTI2_IRQn = 8, /*!< EXTI Line2 Interrupt */
+ EXTI3_IRQn = 9, /*!< EXTI Line3 Interrupt */
+ EXTI4_IRQn = 10, /*!< EXTI Line4 Interrupt */
+ DMA1_Stream0_IRQn = 11, /*!< DMA1 Stream 0 global Interrupt */
+ DMA1_Stream1_IRQn = 12, /*!< DMA1 Stream 1 global Interrupt */
+ DMA1_Stream2_IRQn = 13, /*!< DMA1 Stream 2 global Interrupt */
+ DMA1_Stream3_IRQn = 14, /*!< DMA1 Stream 3 global Interrupt */
+ DMA1_Stream4_IRQn = 15, /*!< DMA1 Stream 4 global Interrupt */
+ DMA1_Stream5_IRQn = 16, /*!< DMA1 Stream 5 global Interrupt */
+ DMA1_Stream6_IRQn = 17, /*!< DMA1 Stream 6 global Interrupt */
+ ADC_IRQn = 18, /*!< ADC1, ADC2 and ADC3 global Interrupts */
+ CAN1_TX_IRQn = 19, /*!< CAN1 TX Interrupt */
+ CAN1_RX0_IRQn = 20, /*!< CAN1 RX0 Interrupt */
+ CAN1_RX1_IRQn = 21, /*!< CAN1 RX1 Interrupt */
+ CAN1_SCE_IRQn = 22, /*!< CAN1 SCE Interrupt */
+ EXTI9_5_IRQn = 23, /*!< External Line[9:5] Interrupts */
+ TIM1_BRK_TIM9_IRQn = 24, /*!< TIM1 Break interrupt and TIM9 global interrupt */
+ TIM1_UP_TIM10_IRQn = 25, /*!< TIM1 Update Interrupt and TIM10 global interrupt */
+ TIM1_TRG_COM_TIM11_IRQn = 26, /*!< TIM1 Trigger and Commutation Interrupt and TIM11 global interrupt */
+ TIM1_CC_IRQn = 27, /*!< TIM1 Capture Compare Interrupt */
+ TIM2_IRQn = 28, /*!< TIM2 global Interrupt */
+ TIM3_IRQn = 29, /*!< TIM3 global Interrupt */
+ TIM4_IRQn = 30, /*!< TIM4 global Interrupt */
+ I2C1_EV_IRQn = 31, /*!< I2C1 Event Interrupt */
+ I2C1_ER_IRQn = 32, /*!< I2C1 Error Interrupt */
+ I2C2_EV_IRQn = 33, /*!< I2C2 Event Interrupt */
+ I2C2_ER_IRQn = 34, /*!< I2C2 Error Interrupt */
+ SPI1_IRQn = 35, /*!< SPI1 global Interrupt */
+ SPI2_IRQn = 36, /*!< SPI2 global Interrupt */
+ USART1_IRQn = 37, /*!< USART1 global Interrupt */
+ USART2_IRQn = 38, /*!< USART2 global Interrupt */
+ USART3_IRQn = 39, /*!< USART3 global Interrupt */
+ EXTI15_10_IRQn = 40, /*!< External Line[15:10] Interrupts */
+ RTC_Alarm_IRQn = 41, /*!< RTC Alarm (A and B) through EXTI Line Interrupt */
+ OTG_FS_WKUP_IRQn = 42, /*!< USB OTG FS Wakeup through EXTI line interrupt */
+ TIM8_BRK_TIM12_IRQn = 43, /*!< TIM8 Break Interrupt and TIM12 global interrupt */
+ TIM8_UP_TIM13_IRQn = 44, /*!< TIM8 Update Interrupt and TIM13 global interrupt */
+ TIM8_TRG_COM_TIM14_IRQn = 45, /*!< TIM8 Trigger and Commutation Interrupt and TIM14 global interrupt */
+ TIM8_CC_IRQn = 46, /*!< TIM8 Capture Compare Interrupt */
+ DMA1_Stream7_IRQn = 47, /*!< DMA1 Stream7 Interrupt */
+ FSMC_IRQn = 48, /*!< FSMC global Interrupt */
+ SDIO_IRQn = 49, /*!< SDIO global Interrupt */
+ TIM5_IRQn = 50, /*!< TIM5 global Interrupt */
+ SPI3_IRQn = 51, /*!< SPI3 global Interrupt */
+ UART4_IRQn = 52, /*!< UART4 global Interrupt */
+ UART5_IRQn = 53, /*!< UART5 global Interrupt */
+ TIM6_DAC_IRQn = 54, /*!< TIM6 global and DAC1&2 underrun error interrupts */
+ TIM7_IRQn = 55, /*!< TIM7 global interrupt */
+ DMA2_Stream0_IRQn = 56, /*!< DMA2 Stream 0 global Interrupt */
+ DMA2_Stream1_IRQn = 57, /*!< DMA2 Stream 1 global Interrupt */
+ DMA2_Stream2_IRQn = 58, /*!< DMA2 Stream 2 global Interrupt */
+ DMA2_Stream3_IRQn = 59, /*!< DMA2 Stream 3 global Interrupt */
+ DMA2_Stream4_IRQn = 60, /*!< DMA2 Stream 4 global Interrupt */
+ ETH_IRQn = 61, /*!< Ethernet global Interrupt */
+ ETH_WKUP_IRQn = 62, /*!< Ethernet Wakeup through EXTI line Interrupt */
+ CAN2_TX_IRQn = 63, /*!< CAN2 TX Interrupt */
+ CAN2_RX0_IRQn = 64, /*!< CAN2 RX0 Interrupt */
+ CAN2_RX1_IRQn = 65, /*!< CAN2 RX1 Interrupt */
+ CAN2_SCE_IRQn = 66, /*!< CAN2 SCE Interrupt */
+ OTG_FS_IRQn = 67, /*!< USB OTG FS global Interrupt */
+ DMA2_Stream5_IRQn = 68, /*!< DMA2 Stream 5 global interrupt */
+ DMA2_Stream6_IRQn = 69, /*!< DMA2 Stream 6 global interrupt */
+ DMA2_Stream7_IRQn = 70, /*!< DMA2 Stream 7 global interrupt */
+ USART6_IRQn = 71, /*!< USART6 global interrupt */
+ I2C3_EV_IRQn = 72, /*!< I2C3 event interrupt */
+ I2C3_ER_IRQn = 73, /*!< I2C3 error interrupt */
+ OTG_HS_EP1_OUT_IRQn = 74, /*!< USB OTG HS End Point 1 Out global interrupt */
+ OTG_HS_EP1_IN_IRQn = 75, /*!< USB OTG HS End Point 1 In global interrupt */
+ OTG_HS_WKUP_IRQn = 76, /*!< USB OTG HS Wakeup through EXTI interrupt */
+ OTG_HS_IRQn = 77, /*!< USB OTG HS global interrupt */
+ DCMI_IRQn = 78, /*!< DCMI global interrupt */
+ CRYP_IRQn = 79, /*!< CRYP crypto global interrupt */
+ HASH_RNG_IRQn = 80, /*!< Hash and Rng global interrupt */
+ FPU_IRQn = 81 /*!< FPU global interrupt */
+} IRQn_Type;
+
+/**
+ * @}
+ */
+
+#include "core_cm4.h" /* Cortex-M4 processor and core peripherals */
+#include "system_stm32f4xx.h"
+#include
+
+
\ No newline at end of file
diff --git a/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/CMSIS/Device/ST/STM32F4xx/Source/Templates/iar/startup_stm32f4xx.s b/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/CMSIS/Device/ST/STM32F4xx/Source/Templates/iar/startup_stm32f4xx.s
new file mode 100644
index 000000000..e1cb15281
--- /dev/null
+++ b/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/CMSIS/Device/ST/STM32F4xx/Source/Templates/iar/startup_stm32f4xx.s
@@ -0,0 +1,629 @@
+;/******************** (C) COPYRIGHT 2011 STMicroelectronics ********************
+;* File Name : startup_stm32f4xx.s
+;* Author : MCD Application Team
+;* Version : V1.0.0
+;* Date : 30-September-2011
+;* Description : STM32F4xx devices vector table for EWARM toolchain.
+;* This module performs:
+;* - Set the initial SP
+;* - Set the initial PC == _iar_program_start,
+;* - Set the vector table entries with the exceptions ISR
+;* address.
+;* - Configure the system clock and the external SRAM mounted on
+;* STM324xG-EVAL board to be used as data memory (optional,
+;* to be enabled by user)
+;* - Branches to main in the C library (which eventually
+;* calls main()).
+;* After Reset the Cortex-M4 processor is in Thread mode,
+;* priority is Privileged, and the Stack is set to Main.
+;********************************************************************************
+;* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+;* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE TIME.
+;* AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY DIRECT,
+;* INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING FROM THE
+;* CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE CODING
+;* INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+;*******************************************************************************/
+;
+;
+; The modules in this file are included in the libraries, and may be replaced
+; by any user-defined modules that define the PUBLIC symbol _program_start or
+; a user defined start symbol.
+; To override the cstartup defined in the library, simply add your modified
+; version to the workbench project.
+;
+; The vector table is normally located at address 0.
+; When debugging in RAM, it can be located in RAM, aligned to at least 2^6.
+; The name "__vector_table" has special meaning for C-SPY:
+; it is where the SP start value is found, and the NVIC vector
+; table register (VTOR) is initialized to this address if != 0.
+;
+; Cortex-M version
+;
+
+ MODULE ?cstartup
+
+ ;; Forward declaration of sections.
+ SECTION CSTACK:DATA:NOROOT(3)
+
+ SECTION .intvec:CODE:NOROOT(2)
+
+ EXTERN __iar_program_start
+ EXTERN SystemInit
+ PUBLIC __vector_table
+
+ DATA
+__vector_table
+ DCD sfe(CSTACK)
+ DCD Reset_Handler ; Reset Handler
+
+ DCD NMI_Handler ; NMI Handler
+ DCD HardFault_Handler ; Hard Fault Handler
+ DCD MemManage_Handler ; MPU Fault Handler
+ DCD BusFault_Handler ; Bus Fault Handler
+ DCD UsageFault_Handler ; Usage Fault Handler
+ DCD 0 ; Reserved
+ DCD 0 ; Reserved
+ DCD 0 ; Reserved
+ DCD 0 ; Reserved
+ DCD SVC_Handler ; SVCall Handler
+ DCD DebugMon_Handler ; Debug Monitor Handler
+ DCD 0 ; Reserved
+ DCD PendSV_Handler ; PendSV Handler
+ DCD SysTick_Handler ; SysTick Handler
+
+ ; External Interrupts
+ DCD WWDG_IRQHandler ; Window WatchDog
+ DCD PVD_IRQHandler ; PVD through EXTI Line detection
+ DCD TAMP_STAMP_IRQHandler ; Tamper and TimeStamps through the EXTI line
+ DCD RTC_WKUP_IRQHandler ; RTC Wakeup through the EXTI line
+ DCD FLASH_IRQHandler ; FLASH
+ DCD RCC_IRQHandler ; RCC
+ DCD EXTI0_IRQHandler ; EXTI Line0
+ DCD EXTI1_IRQHandler ; EXTI Line1
+ DCD EXTI2_IRQHandler ; EXTI Line2
+ DCD EXTI3_IRQHandler ; EXTI Line3
+ DCD EXTI4_IRQHandler ; EXTI Line4
+ DCD DMA1_Stream0_IRQHandler ; DMA1 Stream 0
+ DCD DMA1_Stream1_IRQHandler ; DMA1 Stream 1
+ DCD DMA1_Stream2_IRQHandler ; DMA1 Stream 2
+ DCD DMA1_Stream3_IRQHandler ; DMA1 Stream 3
+ DCD DMA1_Stream4_IRQHandler ; DMA1 Stream 4
+ DCD DMA1_Stream5_IRQHandler ; DMA1 Stream 5
+ DCD DMA1_Stream6_IRQHandler ; DMA1 Stream 6
+ DCD ADC_IRQHandler ; ADC1, ADC2 and ADC3s
+ DCD CAN1_TX_IRQHandler ; CAN1 TX
+ DCD CAN1_RX0_IRQHandler ; CAN1 RX0
+ DCD CAN1_RX1_IRQHandler ; CAN1 RX1
+ DCD CAN1_SCE_IRQHandler ; CAN1 SCE
+ DCD EXTI9_5_IRQHandler ; External Line[9:5]s
+ DCD TIM1_BRK_TIM9_IRQHandler ; TIM1 Break and TIM9
+ DCD TIM1_UP_TIM10_IRQHandler ; TIM1 Update and TIM10
+ DCD TIM1_TRG_COM_TIM11_IRQHandler ; TIM1 Trigger and Commutation and TIM11
+ DCD TIM1_CC_IRQHandler ; TIM1 Capture Compare
+ DCD TIM2_IRQHandler ; TIM2
+ DCD TIM3_IRQHandler ; TIM3
+ DCD TIM4_IRQHandler ; TIM4
+ DCD I2C1_EV_IRQHandler ; I2C1 Event
+ DCD I2C1_ER_IRQHandler ; I2C1 Error
+ DCD I2C2_EV_IRQHandler ; I2C2 Event
+ DCD I2C2_ER_IRQHandler ; I2C2 Error
+ DCD SPI1_IRQHandler ; SPI1
+ DCD SPI2_IRQHandler ; SPI2
+ DCD USART1_IRQHandler ; USART1
+ DCD USART2_IRQHandler ; USART2
+ DCD USART3_IRQHandler ; USART3
+ DCD EXTI15_10_IRQHandler ; External Line[15:10]s
+ DCD RTC_Alarm_IRQHandler ; RTC Alarm (A and B) through EXTI Line
+ DCD OTG_FS_WKUP_IRQHandler ; USB OTG FS Wakeup through EXTI line
+ DCD TIM8_BRK_TIM12_IRQHandler ; TIM8 Break and TIM12
+ DCD TIM8_UP_TIM13_IRQHandler ; TIM8 Update and TIM13
+ DCD TIM8_TRG_COM_TIM14_IRQHandler ; TIM8 Trigger and Commutation and TIM14
+ DCD TIM8_CC_IRQHandler ; TIM8 Capture Compare
+ DCD DMA1_Stream7_IRQHandler ; DMA1 Stream7
+ DCD FSMC_IRQHandler ; FSMC
+ DCD SDIO_IRQHandler ; SDIO
+ DCD TIM5_IRQHandler ; TIM5
+ DCD SPI3_IRQHandler ; SPI3
+ DCD UART4_IRQHandler ; UART4
+ DCD UART5_IRQHandler ; UART5
+ DCD TIM6_DAC_IRQHandler ; TIM6 and DAC1&2 underrun errors
+ DCD TIM7_IRQHandler ; TIM7
+ DCD DMA2_Stream0_IRQHandler ; DMA2 Stream 0
+ DCD DMA2_Stream1_IRQHandler ; DMA2 Stream 1
+ DCD DMA2_Stream2_IRQHandler ; DMA2 Stream 2
+ DCD DMA2_Stream3_IRQHandler ; DMA2 Stream 3
+ DCD DMA2_Stream4_IRQHandler ; DMA2 Stream 4
+ DCD ETH_IRQHandler ; Ethernet
+ DCD ETH_WKUP_IRQHandler ; Ethernet Wakeup through EXTI line
+ DCD CAN2_TX_IRQHandler ; CAN2 TX
+ DCD CAN2_RX0_IRQHandler ; CAN2 RX0
+ DCD CAN2_RX1_IRQHandler ; CAN2 RX1
+ DCD CAN2_SCE_IRQHandler ; CAN2 SCE
+ DCD OTG_FS_IRQHandler ; USB OTG FS
+ DCD DMA2_Stream5_IRQHandler ; DMA2 Stream 5
+ DCD DMA2_Stream6_IRQHandler ; DMA2 Stream 6
+ DCD DMA2_Stream7_IRQHandler ; DMA2 Stream 7
+ DCD USART6_IRQHandler ; USART6
+ DCD I2C3_EV_IRQHandler ; I2C3 event
+ DCD I2C3_ER_IRQHandler ; I2C3 error
+ DCD OTG_HS_EP1_OUT_IRQHandler ; USB OTG HS End Point 1 Out
+ DCD OTG_HS_EP1_IN_IRQHandler ; USB OTG HS End Point 1 In
+ DCD OTG_HS_WKUP_IRQHandler ; USB OTG HS Wakeup through EXTI
+ DCD OTG_HS_IRQHandler ; USB OTG HS
+ DCD DCMI_IRQHandler ; DCMI
+ DCD CRYP_IRQHandler ; CRYP crypto
+ DCD HASH_RNG_IRQHandler ; Hash and Rng
+ DCD FPU_IRQHandler ; FPU
+
+;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
+;;
+;; Default interrupt handlers.
+;;
+ THUMB
+ PUBWEAK Reset_Handler
+ SECTION .text:CODE:REORDER(2)
+Reset_Handler
+
+ LDR R0, =SystemInit
+ BLX R0
+ LDR R0, =__iar_program_start
+ BX R0
+
+ PUBWEAK NMI_Handler
+ SECTION .text:CODE:REORDER(1)
+NMI_Handler
+ B NMI_Handler
+
+ PUBWEAK HardFault_Handler
+ SECTION .text:CODE:REORDER(1)
+HardFault_Handler
+ B HardFault_Handler
+
+ PUBWEAK MemManage_Handler
+ SECTION .text:CODE:REORDER(1)
+MemManage_Handler
+ B MemManage_Handler
+
+ PUBWEAK BusFault_Handler
+ SECTION .text:CODE:REORDER(1)
+BusFault_Handler
+ B BusFault_Handler
+
+ PUBWEAK UsageFault_Handler
+ SECTION .text:CODE:REORDER(1)
+UsageFault_Handler
+ B UsageFault_Handler
+
+ PUBWEAK SVC_Handler
+ SECTION .text:CODE:REORDER(1)
+SVC_Handler
+ B SVC_Handler
+
+ PUBWEAK DebugMon_Handler
+ SECTION .text:CODE:REORDER(1)
+DebugMon_Handler
+ B DebugMon_Handler
+
+ PUBWEAK PendSV_Handler
+ SECTION .text:CODE:REORDER(1)
+PendSV_Handler
+ B PendSV_Handler
+
+ PUBWEAK SysTick_Handler
+ SECTION .text:CODE:REORDER(1)
+SysTick_Handler
+ B SysTick_Handler
+
+ PUBWEAK WWDG_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+WWDG_IRQHandler
+ B WWDG_IRQHandler
+
+ PUBWEAK PVD_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+PVD_IRQHandler
+ B PVD_IRQHandler
+
+ PUBWEAK TAMP_STAMP_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TAMP_STAMP_IRQHandler
+ B TAMP_STAMP_IRQHandler
+
+ PUBWEAK RTC_WKUP_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+RTC_WKUP_IRQHandler
+ B RTC_WKUP_IRQHandler
+
+ PUBWEAK FLASH_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+FLASH_IRQHandler
+ B FLASH_IRQHandler
+
+ PUBWEAK RCC_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+RCC_IRQHandler
+ B RCC_IRQHandler
+
+ PUBWEAK EXTI0_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+EXTI0_IRQHandler
+ B EXTI0_IRQHandler
+
+ PUBWEAK EXTI1_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+EXTI1_IRQHandler
+ B EXTI1_IRQHandler
+
+ PUBWEAK EXTI2_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+EXTI2_IRQHandler
+ B EXTI2_IRQHandler
+
+ PUBWEAK EXTI3_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+EXTI3_IRQHandler
+ B EXTI3_IRQHandler
+
+ PUBWEAK EXTI4_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+EXTI4_IRQHandler
+ B EXTI4_IRQHandler
+
+ PUBWEAK DMA1_Stream0_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA1_Stream0_IRQHandler
+ B DMA1_Stream0_IRQHandler
+
+ PUBWEAK DMA1_Stream1_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA1_Stream1_IRQHandler
+ B DMA1_Stream1_IRQHandler
+
+ PUBWEAK DMA1_Stream2_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA1_Stream2_IRQHandler
+ B DMA1_Stream2_IRQHandler
+
+ PUBWEAK DMA1_Stream3_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA1_Stream3_IRQHandler
+ B DMA1_Stream3_IRQHandler
+
+ PUBWEAK DMA1_Stream4_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA1_Stream4_IRQHandler
+ B DMA1_Stream4_IRQHandler
+
+ PUBWEAK DMA1_Stream5_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA1_Stream5_IRQHandler
+ B DMA1_Stream5_IRQHandler
+
+ PUBWEAK DMA1_Stream6_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA1_Stream6_IRQHandler
+ B DMA1_Stream6_IRQHandler
+
+ PUBWEAK ADC_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+ADC_IRQHandler
+ B ADC_IRQHandler
+
+ PUBWEAK CAN1_TX_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+CAN1_TX_IRQHandler
+ B CAN1_TX_IRQHandler
+
+ PUBWEAK CAN1_RX0_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+CAN1_RX0_IRQHandler
+ B CAN1_RX0_IRQHandler
+
+ PUBWEAK CAN1_RX1_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+CAN1_RX1_IRQHandler
+ B CAN1_RX1_IRQHandler
+
+ PUBWEAK CAN1_SCE_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+CAN1_SCE_IRQHandler
+ B CAN1_SCE_IRQHandler
+
+ PUBWEAK EXTI9_5_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+EXTI9_5_IRQHandler
+ B EXTI9_5_IRQHandler
+
+ PUBWEAK TIM1_BRK_TIM9_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM1_BRK_TIM9_IRQHandler
+ B TIM1_BRK_TIM9_IRQHandler
+
+ PUBWEAK TIM1_UP_TIM10_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM1_UP_TIM10_IRQHandler
+ B TIM1_UP_TIM10_IRQHandler
+
+ PUBWEAK TIM1_TRG_COM_TIM11_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM1_TRG_COM_TIM11_IRQHandler
+ B TIM1_TRG_COM_TIM11_IRQHandler
+
+ PUBWEAK TIM1_CC_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM1_CC_IRQHandler
+ B TIM1_CC_IRQHandler
+
+ PUBWEAK TIM2_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM2_IRQHandler
+ B TIM2_IRQHandler
+
+ PUBWEAK TIM3_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM3_IRQHandler
+ B TIM3_IRQHandler
+
+ PUBWEAK TIM4_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM4_IRQHandler
+ B TIM4_IRQHandler
+
+ PUBWEAK I2C1_EV_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+I2C1_EV_IRQHandler
+ B I2C1_EV_IRQHandler
+
+ PUBWEAK I2C1_ER_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+I2C1_ER_IRQHandler
+ B I2C1_ER_IRQHandler
+
+ PUBWEAK I2C2_EV_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+I2C2_EV_IRQHandler
+ B I2C2_EV_IRQHandler
+
+ PUBWEAK I2C2_ER_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+I2C2_ER_IRQHandler
+ B I2C2_ER_IRQHandler
+
+ PUBWEAK SPI1_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+SPI1_IRQHandler
+ B SPI1_IRQHandler
+
+ PUBWEAK SPI2_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+SPI2_IRQHandler
+ B SPI2_IRQHandler
+
+ PUBWEAK USART1_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+USART1_IRQHandler
+ B USART1_IRQHandler
+
+ PUBWEAK USART2_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+USART2_IRQHandler
+ B USART2_IRQHandler
+
+ PUBWEAK USART3_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+USART3_IRQHandler
+ B USART3_IRQHandler
+
+ PUBWEAK EXTI15_10_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+EXTI15_10_IRQHandler
+ B EXTI15_10_IRQHandler
+
+ PUBWEAK RTC_Alarm_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+RTC_Alarm_IRQHandler
+ B RTC_Alarm_IRQHandler
+
+ PUBWEAK OTG_FS_WKUP_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+OTG_FS_WKUP_IRQHandler
+ B OTG_FS_WKUP_IRQHandler
+
+ PUBWEAK TIM8_BRK_TIM12_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM8_BRK_TIM12_IRQHandler
+ B TIM8_BRK_TIM12_IRQHandler
+
+ PUBWEAK TIM8_UP_TIM13_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM8_UP_TIM13_IRQHandler
+ B TIM8_UP_TIM13_IRQHandler
+
+ PUBWEAK TIM8_TRG_COM_TIM14_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM8_TRG_COM_TIM14_IRQHandler
+ B TIM8_TRG_COM_TIM14_IRQHandler
+
+ PUBWEAK TIM8_CC_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM8_CC_IRQHandler
+ B TIM8_CC_IRQHandler
+
+ PUBWEAK DMA1_Stream7_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA1_Stream7_IRQHandler
+ B DMA1_Stream7_IRQHandler
+
+ PUBWEAK FSMC_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+FSMC_IRQHandler
+ B FSMC_IRQHandler
+
+ PUBWEAK SDIO_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+SDIO_IRQHandler
+ B SDIO_IRQHandler
+
+ PUBWEAK TIM5_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM5_IRQHandler
+ B TIM5_IRQHandler
+
+ PUBWEAK SPI3_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+SPI3_IRQHandler
+ B SPI3_IRQHandler
+
+ PUBWEAK UART4_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+UART4_IRQHandler
+ B UART4_IRQHandler
+
+ PUBWEAK UART5_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+UART5_IRQHandler
+ B UART5_IRQHandler
+
+ PUBWEAK TIM6_DAC_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM6_DAC_IRQHandler
+ B TIM6_DAC_IRQHandler
+
+ PUBWEAK TIM7_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+TIM7_IRQHandler
+ B TIM7_IRQHandler
+
+ PUBWEAK DMA2_Stream0_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA2_Stream0_IRQHandler
+ B DMA2_Stream0_IRQHandler
+
+ PUBWEAK DMA2_Stream1_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA2_Stream1_IRQHandler
+ B DMA2_Stream1_IRQHandler
+
+ PUBWEAK DMA2_Stream2_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA2_Stream2_IRQHandler
+ B DMA2_Stream2_IRQHandler
+
+ PUBWEAK DMA2_Stream3_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA2_Stream3_IRQHandler
+ B DMA2_Stream3_IRQHandler
+
+ PUBWEAK DMA2_Stream4_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA2_Stream4_IRQHandler
+ B DMA2_Stream4_IRQHandler
+
+ PUBWEAK ETH_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+ETH_IRQHandler
+ B ETH_IRQHandler
+
+ PUBWEAK ETH_WKUP_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+ETH_WKUP_IRQHandler
+ B ETH_WKUP_IRQHandler
+
+ PUBWEAK CAN2_TX_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+CAN2_TX_IRQHandler
+ B CAN2_TX_IRQHandler
+
+ PUBWEAK CAN2_RX0_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+CAN2_RX0_IRQHandler
+ B CAN2_RX0_IRQHandler
+
+ PUBWEAK CAN2_RX1_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+CAN2_RX1_IRQHandler
+ B CAN2_RX1_IRQHandler
+
+ PUBWEAK CAN2_SCE_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+CAN2_SCE_IRQHandler
+ B CAN2_SCE_IRQHandler
+
+ PUBWEAK OTG_FS_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+OTG_FS_IRQHandler
+ B OTG_FS_IRQHandler
+
+ PUBWEAK DMA2_Stream5_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA2_Stream5_IRQHandler
+ B DMA2_Stream5_IRQHandler
+
+ PUBWEAK DMA2_Stream6_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA2_Stream6_IRQHandler
+ B DMA2_Stream6_IRQHandler
+
+ PUBWEAK DMA2_Stream7_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DMA2_Stream7_IRQHandler
+ B DMA2_Stream7_IRQHandler
+
+ PUBWEAK USART6_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+USART6_IRQHandler
+ B USART6_IRQHandler
+
+ PUBWEAK I2C3_EV_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+I2C3_EV_IRQHandler
+ B I2C3_EV_IRQHandler
+
+ PUBWEAK I2C3_ER_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+I2C3_ER_IRQHandler
+ B I2C3_ER_IRQHandler
+
+ PUBWEAK OTG_HS_EP1_OUT_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+OTG_HS_EP1_OUT_IRQHandler
+ B OTG_HS_EP1_OUT_IRQHandler
+
+ PUBWEAK OTG_HS_EP1_IN_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+OTG_HS_EP1_IN_IRQHandler
+ B OTG_HS_EP1_IN_IRQHandler
+
+ PUBWEAK OTG_HS_WKUP_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+OTG_HS_WKUP_IRQHandler
+ B OTG_HS_WKUP_IRQHandler
+
+ PUBWEAK OTG_HS_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+OTG_HS_IRQHandler
+ B OTG_HS_IRQHandler
+
+ PUBWEAK DCMI_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+DCMI_IRQHandler
+ B DCMI_IRQHandler
+
+ PUBWEAK CRYP_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+CRYP_IRQHandler
+ B CRYP_IRQHandler
+
+ PUBWEAK HASH_RNG_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+HASH_RNG_IRQHandler
+ B HASH_RNG_IRQHandler
+
+ PUBWEAK FPU_IRQHandler
+ SECTION .text:CODE:REORDER(1)
+FPU_IRQHandler
+ B FPU_IRQHandler
+
+ END
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c b/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c
new file mode 100644
index 000000000..9c31674a4
--- /dev/null
+++ b/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c
@@ -0,0 +1,553 @@
+/**
+ ******************************************************************************
+ * @file system_stm32f4xx.c
+ * @author MCD Application Team
+ * @version V1.0.0
+ * @date 30-September-2011
+ * @brief CMSIS Cortex-M4 Device Peripheral Access Layer System Source File.
+ * This file contains the system clock configuration for STM32F4xx devices,
+ * and is generated by the clock configuration tool
+ * stm32f4xx_Clock_Configuration_V1.0.0.xls
+ *
+ * 1. This file provides two functions and one global variable to be called from
+ * user application:
+ * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier
+ * and Divider factors, AHB/APBx prescalers and Flash settings),
+ * depending on the configuration made in the clock xls tool.
+ * This function is called at startup just after reset and
+ * before branch to main program. This call is made inside
+ * the "startup_stm32f4xx.s" file.
+ *
+ * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
+ * by the user application to setup the SysTick
+ * timer or configure other parameters.
+ *
+ * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
+ * be called whenever the core clock is changed
+ * during program execution.
+ *
+ * 2. After each device reset the HSI (16 MHz) is used as system clock source.
+ * Then SystemInit() function is called, in "startup_stm32f4xx.s" file, to
+ * configure the system clock before to branch to main program.
+ *
+ * 3. If the system clock source selected by user fails to startup, the SystemInit()
+ * function will do nothing and HSI still used as system clock source. User can
+ * add some code to deal with this issue inside the SetSysClock() function.
+ *
+ * 4. The default value of HSE crystal is set to 25MHz, refer to "HSE_VALUE" define
+ * in "stm32f4xx.h" file. When HSE is used as system clock source, directly or
+ * through PLL, and you are using different crystal you have to adapt the HSE
+ * value to your own configuration.
+ *
+ * 5. This file configures the system clock as follows:
+ *=============================================================================
+ *=============================================================================
+ * Supported STM32F4xx device revision | Rev A
+ *-----------------------------------------------------------------------------
+ * System Clock source | PLL (HSE)
+ *-----------------------------------------------------------------------------
+ * SYSCLK(Hz) | 168000000
+ *-----------------------------------------------------------------------------
+ * HCLK(Hz) | 168000000
+ *-----------------------------------------------------------------------------
+ * AHB Prescaler | 1
+ *-----------------------------------------------------------------------------
+ * APB1 Prescaler | 4
+ *-----------------------------------------------------------------------------
+ * APB2 Prescaler | 2
+ *-----------------------------------------------------------------------------
+ * HSE Frequency(Hz) | 25000000
+ *-----------------------------------------------------------------------------
+ * PLL_M | 25
+ *-----------------------------------------------------------------------------
+ * PLL_N | 336
+ *-----------------------------------------------------------------------------
+ * PLL_P | 2
+ *-----------------------------------------------------------------------------
+ * PLL_Q | 7
+ *-----------------------------------------------------------------------------
+ * PLLI2S_N | NA
+ *-----------------------------------------------------------------------------
+ * PLLI2S_R | NA
+ *-----------------------------------------------------------------------------
+ * I2S input clock | NA
+ *-----------------------------------------------------------------------------
+ * VDD(V) | 3.3
+ *-----------------------------------------------------------------------------
+ * Main regulator output voltage | Scale1 mode
+ *-----------------------------------------------------------------------------
+ * Flash Latency(WS) | 5
+ *-----------------------------------------------------------------------------
+ * Prefetch Buffer | OFF
+ *-----------------------------------------------------------------------------
+ * Instruction cache | ON
+ *-----------------------------------------------------------------------------
+ * Data cache | ON
+ *-----------------------------------------------------------------------------
+ * Require 48MHz for USB OTG FS, | Enabled
+ * SDIO and RNG clock |
+ *-----------------------------------------------------------------------------
+ *=============================================================================
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+
+
+
+
+
+
+
+
|
+
© COPYRIGHT 2011 STMicroelectronics
+ ******************************************************************************
+ */
+
+/** @addtogroup CMSIS
+ * @{
+ */
+
+/** @addtogroup stm32f4xx_system
+ * @{
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Includes
+ * @{
+ */
+
+#include "stm32f4xx.h"
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_TypesDefinitions
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Defines
+ * @{
+ */
+
+/************************* Miscellaneous Configuration ************************/
+/*!< Uncomment the following line if you need to use external SRAM mounted
+ on STM324xG_EVAL board as data memory */
+/* #define DATA_IN_ExtSRAM */
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+ Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET 0x00 /*!< Vector Table base offset field.
+ This value must be a multiple of 0x200. */
+/******************************************************************************/
+
+/************************* PLL Parameters *************************************/
+/* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N */
+#define PLL_M 25
+#define PLL_N 336
+
+/* SYSCLK = PLL_VCO / PLL_P */
+#define PLL_P 2
+
+/* USB OTG FS, SDIO and RNG Clock = PLL_VCO / PLLQ */
+#define PLL_Q 7
+
+/******************************************************************************/
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Macros
+ * @{
+ */
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Variables
+ * @{
+ */
+
+ uint32_t SystemCoreClock = 168000000;
+
+ __I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_FunctionPrototypes
+ * @{
+ */
+
+static void SetSysClock(void);
+#ifdef DATA_IN_ExtSRAM
+ static void SystemInit_ExtMemCtl(void);
+#endif /* DATA_IN_ExtSRAM */
+
+/**
+ * @}
+ */
+
+/** @addtogroup STM32F4xx_System_Private_Functions
+ * @{
+ */
+
+/**
+ * @brief Setup the microcontroller system
+ * Initialize the Embedded Flash Interface, the PLL and update the
+ * SystemFrequency variable.
+ * @param None
+ * @retval None
+ */
+void SystemInit(void)
+{
+ /* FPU settings ------------------------------------------------------------*/
+ #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+ SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2)); /* set CP10 and CP11 Full Access */
+ #endif
+
+ /* Reset the RCC clock configuration to the default reset state ------------*/
+ /* Set HSION bit */
+ RCC->CR |= (uint32_t)0x00000001;
+
+ /* Reset CFGR register */
+ RCC->CFGR = 0x00000000;
+
+ /* Reset HSEON, CSSON and PLLON bits */
+ RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+ /* Reset PLLCFGR register */
+ RCC->PLLCFGR = 0x24003010;
+
+ /* Reset HSEBYP bit */
+ RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+ /* Disable all interrupts */
+ RCC->CIR = 0x00000000;
+
+#ifdef DATA_IN_ExtSRAM
+ SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM */
+
+ /* Configure the System clock source, PLL Multiplier and Divider factors,
+ AHB/APBx prescalers and Flash settings ----------------------------------*/
+ SetSysClock();
+
+ /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+ SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+ SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+}
+
+/**
+ * @brief Update SystemCoreClock variable according to Clock Register Values.
+ * The SystemCoreClock variable contains the core clock (HCLK), it can
+ * be used by the user application to setup the SysTick timer or configure
+ * other parameters.
+ *
+ * @note Each time the core clock (HCLK) changes, this function must be called
+ * to update SystemCoreClock variable value. Otherwise, any configuration
+ * based on this variable will be incorrect.
+ *
+ * @note - The system frequency computed by this function is not the real
+ * frequency in the chip. It is calculated based on the predefined
+ * constant and the selected clock source:
+ *
+ * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
+ *
+ * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
+ *
+ * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**)
+ * or HSI_VALUE(*) multiplied/divided by the PLL factors.
+ *
+ * (*) HSI_VALUE is a constant defined in stm32f4xx.h file (default value
+ * 16 MHz) but the real value may vary depending on the variations
+ * in voltage and temperature.
+ *
+ * (**) HSE_VALUE is a constant defined in stm32f4xx.h file (default value
+ * 25 MHz), user has to ensure that HSE_VALUE is same as the real
+ * frequency of the crystal used. Otherwise, this function may
+ * have wrong result.
+ *
+ * - The result of this function could be not correct when using fractional
+ * value for HSE crystal.
+ *
+ * @param None
+ * @retval None
+ */
+void SystemCoreClockUpdate(void)
+{
+ uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
+
+ /* Get SYSCLK source -------------------------------------------------------*/
+ tmp = RCC->CFGR & RCC_CFGR_SWS;
+
+ switch (tmp)
+ {
+ case 0x00: /* HSI used as system clock source */
+ SystemCoreClock = HSI_VALUE;
+ break;
+ case 0x04: /* HSE used as system clock source */
+ SystemCoreClock = HSE_VALUE;
+ break;
+ case 0x08: /* PLL used as system clock source */
+
+ /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
+ SYSCLK = PLL_VCO / PLL_P
+ */
+ pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
+ pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
+
+ if (pllsource != 0)
+ {
+ /* HSE used as PLL clock source */
+ pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
+ }
+ else
+ {
+ /* HSI used as PLL clock source */
+ pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
+ }
+
+ pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
+ SystemCoreClock = pllvco/pllp;
+ break;
+ default:
+ SystemCoreClock = HSI_VALUE;
+ break;
+ }
+ /* Compute HCLK frequency --------------------------------------------------*/
+ /* Get HCLK prescaler */
+ tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
+ /* HCLK frequency */
+ SystemCoreClock >>= tmp;
+}
+
+/**
+ * @brief Configures the System clock source, PLL Multiplier and Divider factors,
+ * AHB/APBx prescalers and Flash settings
+ * @Note This function should be called only once the RCC clock configuration
+ * is reset to the default reset state (done in SystemInit() function).
+ * @param None
+ * @retval None
+ */
+static void SetSysClock(void)
+{
+/******************************************************************************/
+/* PLL (clocked by HSE) used as System clock source */
+/******************************************************************************/
+ __IO uint32_t StartUpCounter = 0, HSEStatus = 0;
+
+ /* Enable HSE */
+ RCC->CR |= ((uint32_t)RCC_CR_HSEON);
+
+ /* Wait till HSE is ready and if Time out is reached exit */
+ do
+ {
+ HSEStatus = RCC->CR & RCC_CR_HSERDY;
+ StartUpCounter++;
+ } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT));
+
+ if ((RCC->CR & RCC_CR_HSERDY) != RESET)
+ {
+ HSEStatus = (uint32_t)0x01;
+ }
+ else
+ {
+ HSEStatus = (uint32_t)0x00;
+ }
+
+ if (HSEStatus == (uint32_t)0x01)
+ {
+ /* Select regulator voltage output Scale 1 mode, System frequency up to 168 MHz */
+ RCC->APB1ENR |= RCC_APB1ENR_PWREN;
+ PWR->CR |= PWR_CR_VOS;
+
+ /* HCLK = SYSCLK / 1*/
+ RCC->CFGR |= RCC_CFGR_HPRE_DIV1;
+
+ /* PCLK2 = HCLK / 2*/
+ RCC->CFGR |= RCC_CFGR_PPRE2_DIV2;
+
+ /* PCLK1 = HCLK / 4*/
+ RCC->CFGR |= RCC_CFGR_PPRE1_DIV4;
+
+ /* Configure the main PLL */
+ RCC->PLLCFGR = PLL_M | (PLL_N << 6) | (((PLL_P >> 1) -1) << 16) |
+ (RCC_PLLCFGR_PLLSRC_HSE) | (PLL_Q << 24);
+
+ /* Enable the main PLL */
+ RCC->CR |= RCC_CR_PLLON;
+
+ /* Wait till the main PLL is ready */
+ while((RCC->CR & RCC_CR_PLLRDY) == 0)
+ {
+ }
+
+ /* Configure Flash prefetch, Instruction cache, Data cache and wait state */
+ FLASH->ACR = FLASH_ACR_ICEN |FLASH_ACR_DCEN |FLASH_ACR_LATENCY_5WS;
+
+ /* Select the main PLL as system clock source */
+ RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW));
+ RCC->CFGR |= RCC_CFGR_SW_PLL;
+
+ /* Wait till the main PLL is used as system clock source */
+ while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS ) != RCC_CFGR_SWS_PLL);
+ {
+ }
+ }
+ else
+ { /* If HSE fails to start-up, the application will have wrong clock
+ configuration. User can add here some code to deal with this error */
+ }
+
+}
+
+/**
+ * @brief Setup the external memory controller. Called in startup_stm32f4xx.s
+ * before jump to __main
+ * @param None
+ * @retval None
+ */
+#ifdef DATA_IN_ExtSRAM
+/**
+ * @brief Setup the external memory controller.
+ * Called in startup_stm32f4xx.s before jump to main.
+ * This function configures the external SRAM mounted on STM324xG_EVAL board
+ * This SRAM will be used as program data memory (including heap and stack).
+ * @param None
+ * @retval None
+ */
+void SystemInit_ExtMemCtl(void)
+{
+/*-- GPIOs Configuration -----------------------------------------------------*/
+/*
+ +-------------------+--------------------+------------------+------------------+
+ + SRAM pins assignment +
+ +-------------------+--------------------+------------------+------------------+
+ | PD0 <-> FSMC_D2 | PE0 <-> FSMC_NBL0 | PF0 <-> FSMC_A0 | PG0 <-> FSMC_A10 |
+ | PD1 <-> FSMC_D3 | PE1 <-> FSMC_NBL1 | PF1 <-> FSMC_A1 | PG1 <-> FSMC_A11 |
+ | PD4 <-> FSMC_NOE | PE3 <-> FSMC_A19 | PF2 <-> FSMC_A2 | PG2 <-> FSMC_A12 |
+ | PD5 <-> FSMC_NWE | PE4 <-> FSMC_A20 | PF3 <-> FSMC_A3 | PG3 <-> FSMC_A13 |
+ | PD8 <-> FSMC_D13 | PE7 <-> FSMC_D4 | PF4 <-> FSMC_A4 | PG4 <-> FSMC_A14 |
+ | PD9 <-> FSMC_D14 | PE8 <-> FSMC_D5 | PF5 <-> FSMC_A5 | PG5 <-> FSMC_A15 |
+ | PD10 <-> FSMC_D15 | PE9 <-> FSMC_D6 | PF12 <-> FSMC_A6 | PG9 <-> FSMC_NE2 |
+ | PD11 <-> FSMC_A16 | PE10 <-> FSMC_D7 | PF13 <-> FSMC_A7 |------------------+
+ | PD12 <-> FSMC_A17 | PE11 <-> FSMC_D8 | PF14 <-> FSMC_A8 |
+ | PD13 <-> FSMC_A18 | PE12 <-> FSMC_D9 | PF15 <-> FSMC_A9 |
+ | PD14 <-> FSMC_D0 | PE13 <-> FSMC_D10 |------------------+
+ | PD15 <-> FSMC_D1 | PE14 <-> FSMC_D11 |
+ | | PE15 <-> FSMC_D12 |
+ +-------------------+--------------------+
+*/
+ /* Enable GPIOD, GPIOE, GPIOF and GPIOG interface clock */
+ RCC->AHB1ENR = 0x00000078;
+
+ /* Connect PDx pins to FSMC Alternate function */
+ GPIOD->AFR[0] = 0x00cc00cc;
+ GPIOD->AFR[1] = 0xcc0ccccc;
+ /* Configure PDx pins in Alternate function mode */
+ GPIOD->MODER = 0xaaaa0a0a;
+ /* Configure PDx pins speed to 100 MHz */
+ GPIOD->OSPEEDR = 0xffff0f0f;
+ /* Configure PDx pins Output type to push-pull */
+ GPIOD->OTYPER = 0x00000000;
+ /* No pull-up, pull-down for PDx pins */
+ GPIOD->PUPDR = 0x00000000;
+
+ /* Connect PEx pins to FSMC Alternate function */
+ GPIOE->AFR[0] = 0xc00cc0cc;
+ GPIOE->AFR[1] = 0xcccccccc;
+ /* Configure PEx pins in Alternate function mode */
+ GPIOE->MODER = 0xaaaa828a;
+ /* Configure PEx pins speed to 100 MHz */
+ GPIOE->OSPEEDR = 0xffffc3cf;
+ /* Configure PEx pins Output type to push-pull */
+ GPIOE->OTYPER = 0x00000000;
+ /* No pull-up, pull-down for PEx pins */
+ GPIOE->PUPDR = 0x00000000;
+
+ /* Connect PFx pins to FSMC Alternate function */
+ GPIOF->AFR[0] = 0x00cccccc;
+ GPIOF->AFR[1] = 0xcccc0000;
+ /* Configure PFx pins in Alternate function mode */
+ GPIOF->MODER = 0xaa000aaa;
+ /* Configure PFx pins speed to 100 MHz */
+ GPIOF->OSPEEDR = 0xff000fff;
+ /* Configure PFx pins Output type to push-pull */
+ GPIOF->OTYPER = 0x00000000;
+ /* No pull-up, pull-down for PFx pins */
+ GPIOF->PUPDR = 0x00000000;
+
+ /* Connect PGx pins to FSMC Alternate function */
+ GPIOG->AFR[0] = 0x00cccccc;
+ GPIOG->AFR[1] = 0x000000c0;
+ /* Configure PGx pins in Alternate function mode */
+ GPIOG->MODER = 0x00080aaa;
+ /* Configure PGx pins speed to 100 MHz */
+ GPIOG->OSPEEDR = 0x000c0fff;
+ /* Configure PGx pins Output type to push-pull */
+ GPIOG->OTYPER = 0x00000000;
+ /* No pull-up, pull-down for PGx pins */
+ GPIOG->PUPDR = 0x00000000;
+
+/*-- FSMC Configuration ------------------------------------------------------*/
+ /* Enable the FSMC interface clock */
+ RCC->AHB3ENR = 0x00000001;
+
+ /* Configure and enable Bank1_SRAM2 */
+ FSMC_Bank1->BTCR[2] = 0x00001015;
+ FSMC_Bank1->BTCR[3] = 0x00010603;
+ FSMC_Bank1E->BWTR[2] = 0x0fffffff;
+/*
+ Bank1_SRAM2 is configured as follow:
+
+ p.FSMC_AddressSetupTime = 3;
+ p.FSMC_AddressHoldTime = 0;
+ p.FSMC_DataSetupTime = 6;
+ p.FSMC_BusTurnAroundDuration = 1;
+ p.FSMC_CLKDivision = 0;
+ p.FSMC_DataLatency = 0;
+ p.FSMC_AccessMode = FSMC_AccessMode_A;
+
+ FSMC_NORSRAMInitStructure.FSMC_Bank = FSMC_Bank1_NORSRAM2;
+ FSMC_NORSRAMInitStructure.FSMC_DataAddressMux = FSMC_DataAddressMux_Disable;
+ FSMC_NORSRAMInitStructure.FSMC_MemoryType = FSMC_MemoryType_PSRAM;
+ FSMC_NORSRAMInitStructure.FSMC_MemoryDataWidth = FSMC_MemoryDataWidth_16b;
+ FSMC_NORSRAMInitStructure.FSMC_BurstAccessMode = FSMC_BurstAccessMode_Disable;
+ FSMC_NORSRAMInitStructure.FSMC_AsynchronousWait = FSMC_AsynchronousWait_Disable;
+ FSMC_NORSRAMInitStructure.FSMC_WaitSignalPolarity = FSMC_WaitSignalPolarity_Low;
+ FSMC_NORSRAMInitStructure.FSMC_WrapMode = FSMC_WrapMode_Disable;
+ FSMC_NORSRAMInitStructure.FSMC_WaitSignalActive = FSMC_WaitSignalActive_BeforeWaitState;
+ FSMC_NORSRAMInitStructure.FSMC_WriteOperation = FSMC_WriteOperation_Enable;
+ FSMC_NORSRAMInitStructure.FSMC_WaitSignal = FSMC_WaitSignal_Disable;
+ FSMC_NORSRAMInitStructure.FSMC_ExtendedMode = FSMC_ExtendedMode_Disable;
+ FSMC_NORSRAMInitStructure.FSMC_WriteBurst = FSMC_WriteBurst_Disable;
+ FSMC_NORSRAMInitStructure.FSMC_ReadWriteTimingStruct = &p;
+ FSMC_NORSRAMInitStructure.FSMC_WriteTimingStruct = &p;
+*/
+
+}
+#endif /* DATA_IN_ExtSRAM */
+
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
diff --git a/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/STM32F4xx_StdPeriph_Driver/Release_Notes.html b/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/STM32F4xx_StdPeriph_Driver/Release_Notes.html
new file mode 100644
index 000000000..c2baed869
--- /dev/null
+++ b/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/STM32F4xx_StdPeriph_Driver/Release_Notes.html
@@ -0,0 +1,958 @@
+
+
+
+
+
+
+
+
+
+
+
+
+
\ No newline at end of file
diff --git a/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/STM32F4xx_StdPeriph_Driver/inc/misc.h b/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/STM32F4xx_StdPeriph_Driver/inc/misc.h
new file mode 100644
index 000000000..7a203eeb6
--- /dev/null
+++ b/Demo/CORTEX_M4F_STM32F407ZG-SK/Libraries/STM32F4xx_StdPeriph_Driver/inc/misc.h
@@ -0,0 +1,172 @@
+/**
+ ******************************************************************************
+ * @file misc.h
+ * @author MCD Application Team
+ * @version V1.0.0
+ * @date 30-September-2011
+ * @brief This file contains all the functions prototypes for the miscellaneous
+ * firmware library functions (add-on to CMSIS functions).
+ ******************************************************************************
+ * @attention
+ *
+ * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
+ * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
+ * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
+ * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
+ * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
+ * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
+ *
+ *
+
+
+
+
+
+
+
+
+
|
+
